The remote control is a fixed frequency type free cloner to copy all kinds of cars, switches and other anti-theft remote. Has a copy and fired as one, suitable for copying a variety of fixed code remote control. 

 First, the works briefly: 
 The remote control receiver sensor to launch the remote control signal, and can detect a high field strength close to launch remote, according to this principle of design This remote control receive mode and transmit mode, from the microcomputer IC learning signal and stored, and transferred to the transmit mode, and then transferred to a response within yards and out to match the antenna emission. 

 Second, the remote control of parameters and settings as follows: 
 [1] Performance: 
 1, this latest Lightning learning techniques usually require only 1 second to quickly flashing learning. Optional frequency of 303M, 310M, 315M, 330M, 350M, 370M, 390M, 418M, 430M, 433MHZ, etc.. 
 2, this product can be copied to the IC model 2262,2260,1527,2240 and compatible IC. 

 3, without regard to shock resistance, this product will be automatically compatible with the shock resistance. 

 4 This product can not copy the IC, such as HCS300/301 and compatible with rolling code IC. 

 This product uses the battery for 12V/27A replace the battery when the remote control distance is insufficient. 




 [2] copy method: before you buy, make sure your original remote control chip model and the operating frequency. 

 You can open a remote shell to know the chip type and frequency of their remote control to see SAW not have to write 315 or 433, and the like number is not written on the chip: 2262 \ 2260 \ 2240 \ 1527 \ PT2264 digital, if that is the case directly photographed, and then sent me the parameters. 

 Or provide you with three pictures of your original remote control: remote control the appearance of a positive picture, the front of the internal circuit boards and a clear picture, the internal circuit board on the back of a clear picture 

 This section remote control operation is very simple, very convenient; at home with remote control, easy to get. Do not need too much expertise, not on the remote control encoding settings, easy steps you can quickly copy a wide variety of frequency fixed code remote control (30, the owner has to help you delete the original code, you go back to direct and your original remote control Duikao what you can, step, easy) This product uses sound frequency stabilization, frequency is fixed, so the performance is very stable. 


 1, clear: while holding down the lock and shut up, 2 seconds after the LED light starts to blink, let go again by pressing any key, short light flash is not bright, which indicates that the original code has been cleared. 


 Copy: take the left the original remote control, right hand holding the remote control of our Self, two remote control as close as possible. Locked key while pressing the two remote (your original remote control and self-copy remote control), after 2 seconds the LED will flashes quickly, then let go and then press the learning key after the success of the light display long bright , which indicates that the original remote locking key code to copy the remote control learning into our self- The other three buttons is the same operation. 



 Recovery: When you accidentally clear the self-copy the code of the remote control, you can press the start (bell) and mute (lightning), the LED light will quickly flash, let go again, press any key, long bright lights, this that since copy the code of the remote control to be restored. Before using our self-copy the remote control to copy, be sure to clear the existing self-copy remote control code first. 



 4 Here is a test since the copy of the code of the remote control has not been successfully cleared: 

 When you end the action of the Qing code, you can press any key of the self-copy, if this time the LED is flashing went out, not lit, it shows that since the copy of the code has been completely cleared, if the LED is light condition, copy the code since there. 



 5 Press to Press after one of the keys can not be controlled, the rest can be controlled, you can use the tips of cleanup and recovery operations: 

 Copy after a button is not successful, while other buttons are normal, then, you can use this little trick. The specific operation is as follows: 

 (1), first Qing yards operations; 

 (2), just did not successfully copy button to copy once, copy the success of the buttons do not copy; 


 (3), then the clear code operation; 

 (4), the restore operation again; 

 At this time, the previously failed copy button just copy the code coverage, while the original copy code preserved, we can use this to reduce repeat trouble.